Gerhard Petri Vilnius UAB

Nexans
e-paslaugos

End sleeves for 1 kV cables with oil-paper insulation

Cable

The end sleeves are designed for armored and unarmoured 3 and 4-core plastic insulated cables and 3 and 4-core cables with oil-paper insulation, including cables with reduced neutral.
E.g.: NAYBY, NAKBA, BBΓ, ΠBΓ, AΠBΓ, AABvU, ACBU.

End sleeve design for paper-insulated cable

Thermoshrink tubes shall be planted on the prepared cores of the oil cable. All materials shall be resistant to UV solar radiation, atmospheric agents, and cable oil. The cable strands can be cut to the required length at the installation site. The heat-shrink glove and the tubing prevent moisture from entering the cable and oil from escaping from the cable through the end of the metal sheath or through the ends of the cores. The kit includes a non-solderable earthing fitting for the metallic sheath of the cable, consisting of a contact spring, an earthing conductor, a copper grid and an insulating tube. The sleeve set also includes auxiliary materials for cable preparation. The kits marked with the modification code -L12 include screw sockets with a bore diameter suitable for M12 screws and -L16 for M16 screws.

For triangular cables

The end sleeve set shall additionally include a non-solderable neutral connection system for aluminum sheathed cable consisting of stainless steel clamps, earthing conductors, and screw terminals.




    End sleeve sets for three-conductor paper insulated cables

    Cross-section of the cores (mm²) Product code for ordering
    Core length L1 (mm)*
    250×4=1000                                 750×4=3000                                 1000×4=4000
    Dimensions
    L₃ (mm)                 L₂ (mm)
    Without lugs
    25-70 GUST 01/3×25-70/250 GUST 01/3×25-70/750 GUST 01/3×25-70/1000 165 80
    70-120 GUST 01/3×70-120/250 GUST 01/3×70-120/750 GUST 01/3×70-120/1000 215 100
    120-240 GUST 01/3×120-240/250 GUST 01/3×120-240/750 GUST 01/3×120-240/1000 220 150
    With screw lugs
    25-70 GUST 01/3×25-70/250-L12 GUST 01/3×25-70/750-L12 GUST 01/3×25-70/1000-L12 165 80
    70-120 GUST 01/3×70-120/250-L12 GUST 01/3×70-120/750-L12 GUST 01/3×70-120/1000-L12 215 100
    120-240 GUST 01/3×120-240/250-L12 GUST 01/3×120-240/750-L12 GUST 01/3×120-240/1000-L12 220 150

    * The length of the core L1 can be adjusted on-site according to the required measurements for each case. The minimum length of the core is 100 mm. The sum of all the lengths L1 of all the cores shall not exceed the standard length L1 given in the table multiplied by 4.

    End sleeve sets for four-core paper insulated cables

    Cross-section of the cores (mm²) Product code for ordering
    Core length L1 (mm)*
    250×4=1000                                   750×4=3000                               1000×4=4000
    Dimensions
    L₃ (mm)                          L₂ (mm)
    Without lugs
    4-25 GUST 01/4×4-25/250 GUST 01/4×4-25/750 GUST 01/4×4-25/1000 95 50
    16-70 GUST 01/4×16-70/250 GUST 01/4×16-70/750 GUST 01/4×16-70/1000 165 80
    70-150 GUST 01/4×70-150/250 GUST 01/4×70-150/750 GUST 01/4×70-150/1000 215 100
    120-240 GUST 01/4×120-240/250 GUST 01/4×120-240/750 GUST 01/4×120-240/1000 220 150
    With screw lugs
    25-70 GUST 01/4×25-70/250-L12 GUST 01/4×25-70/750-L12 GUST 01/4×25-70/1000-L12 165 80
    70-150 GUST 01/4×70-150/250-L12 GUST 01/4×70-150/750-L12 GUST 01/4×70-150/1000-L12 215 100
    120-240 GUST 01/4×120-240/250-L12 GUST 01/4×120-240/750-L12 GUST 01/4×120-240/1000-L12 220 150

    * The length of the core L1 can be adjusted on-site according to the required measurements for each case. The minimum length of the core is 100 mm. The sum of all the lengths L1 of all the cores shall not exceed the standard length L1 given in the table multiplied by 4.

    Panašios prekės